I was contacted just before Christmas by a couple who had bought a house in the southern resort of Bognor Regis that they hoped to spend the festive season in; apart from a new coat of paint and carpet their main concern was the state of the Terracotta tiled floor in the hall, kitchen and dining room. On my initial site inspection it was clear that there were years of grime build up caused by the previous owner’s dogs coming into the house onto a poorly sealed floor. After assuring the client that I was confident that the floor could be bought back to life a price was agreed and a date fixed. I estimated it would take two days to carry out the work with a gap of two days in between to allow the floor to fully dry out.
Deep Cleaning Terracotta Tiles
On the first day I prepared a warm water dilution of Tile Doctor Pro-Clean and worked this into the tile surface and grout using a hand brush and then the buffing machine fitted with a black scrubbing pad. This lifted all the residual dirt, grime and remaining sealer if any. After vacuuming up the dirty solution using a wet Vac the floor was then rinsed several times with clean water to make sure that there was no cleaner or dirt left in or around the tiles.
There were a few stubborn areas where it was necessary to repeat the process and then the whole floor was given a final rinse using the wet vacuum and sponge to get the surface as dry as possible before being left to dry for two days. The tiles were covered with dust sheets in any area that was required for access in order to keep them clean whilst drying out.
Sealing Terracotta Tiles
After allowing the floor to dry out I returned to the property and using my moisture meter tested the floor in several areas to make sure that it was ready to be sealed (I had previously warned the clients that if it wasn’t then further time would have to be given). Satisfied that all was well I set about sealing it, first with a coat of Tile Doctor Colour Grow which was allowed to cure and then followed by five coats of Tile Doctor Seal and Go. Colour Grow is an impregnating sealer that seeps into the pores of the stone protecting it from the inside and as a bonus enhances colour whilst Seal and Go is a topical sealer that protects the surface and also adds a nice sheen to the tile. The end result was everything that I imagined it would be and the clients were very pleased with it also saying that they never thought it would ever look as good as it did. As I said to them ‘I’m no magician but I am a (Tile) Doctor!!
Terracotta tiled floor deep cleaned and sealed in West Sussex
We were contacted by a letting agent who managed a large town house in Goring by Sea that had been turned into flats. The area they wanted dealing with was the entrance hall where the original Victorian tiled floor had been covered over with linoleum tiles backed with a bitumen based adhesive and after removing the tiles the floor was now in a terrible state. I was confident that they could be restored however in extreme cases like this there can be no guarantee of the end result so I set their expectations accordingly.
Restoring Victorian Floor Tiles
I started the job by softening the old adhesive with an application of Tile Doctor Remove and Go which was left to soak into the tile before using a paint stripping blade to carefully lift it off. This process had to be done over the entire area before I could start on the cleaning and once finished the floor was given a good rinse.
The tiles were now mostly free of the adhesive but were very grubby so I started over but this by time by applying a strong dilution of Tile Doctor Pro-Clean which is a powerful tile cleaning product designed for use on stone, tile and grout. The solution was left to soak into the tile before being worked into the remaining dirt and grime using a buffing machine fitted with a scrubbing pad. One done the floor was thoroughly rinsed and any areas that needed it were spot treated.
Sealing a Victorian Floor Tiles
The floor was left to dry out for a few days after which we came back to seal it with four coats of Tile Doctor Pro-Seal which is a penetrating sealer which gave the desired natural look finish and will provide long lasting stain protection by soaking into the pores of the tile and preventing dirt from becoming ingrained there. You have to wait for each coat to dry before moving on to the next so it did take a while.
This was a tough job but certainly well worth the effort both the letting agents and residents all said how great the floor now looked.
Similar to Terracotta these clay floor tiles had been installed throughout the ground floor of this house in Billingshurst including the hall, utility, WC and kitchen. The owner of the property had recently moved out into a new house and was planning on renting it out however none of the tiles had seen any sealer in a long time and although the tiles were in good condition they had a rough finish which had resulted in patchy grout smears as well as the general grime and old sealer build up that needed to be deep cleaned to get the tiles back to their former glory.
Cleaning Old Clay Tiles
To clean the floor I first applied a strong dilution of Tile Doctor Pro-Clean and worked it into every nook and cranny using a hand brush and deck broom. After 10 minutes I used a buffing machine fitted with a black scrubbing pad and worked it over the areas until satisfied that all was clean. After washing the floors down several times to neutralise the cleaning agent and extracting with a wet vacuum I checked the entire area for any problem spots. There were a few stubborn areas that needed re-treating but the main issue was the grout smears which must have been then since the floor was laid. Fortunately we have a solution for most problems and in this case we have a product called Tile Doctor Grout Clean-Up which is very good at removing grout from tile, it an acid based product so you can’t leave it on the tile too long and once it’s worked its magic you need to wash the floor down again to remove any trace of chemical.
Sealing Old Clay Tiles
I left for the evening and returned two days later to ensure the floor would be dry which it was. The tiles need to dry to achieve the best results with the sealer which in this case was Tile Doctor Seal and Go which is a water based sealer that adds a subtle shine effect as well as providing lasting stain protection. Four coats of sealer were required and as you can see from the photographs the difference is quite remarkable.
The pictures below are from a Victorian tiled floor installed in a period house in the coastal town Eastbourne. The tiles had been covered lino and carpet for years which the owner had only recently removed during renovation work, as it turns out this was unfortunate as they then became covered in plaster and paint from the decorators. Although the floor did look to be in a very sorry state I was very confident that I could breathe new life into it given enough time so I allowed four days to complete the task.
Cleaning a Victorian Floor Tiles
Some type of adhesive had been used to stick down the Lino and Carpet so the first step was to remove all the stubborn glue build up which I did using Tile Doctor Remove and Go, then once the bad areas had been targeted I concentrated on the plaster and paint build up which I treated using a 3-1 mix of Tile Doctor Pro-Clean in warm water worked in with a buffing machine fitted with a black scrubbing pad. The soiled water was rinsed away using a wet vacuum so the floor could be checked to see if more work was required which it was so stubborn areas that had resisted the initial cleaning onslaught were spot cleaned by using a diluted mix of Tile Doctor Grout Clean-up which is a very strong acidic product for removing grout and other mineral based substances from tiles. Before finishing the entire floor was given a thorough rinse to remove any trace of cleaning product, again a wet vacuum was used to remove the water and this time get the floor as dry as possible.
Sealing the Victorian Tiled Floor
The cleaning took place over two days and then the floor was given a further two days to allow it to dry fully after which I went back and sealed it with four coats of Tile Doctor Seal and Go which is an ideal sealer for Victorian tiles as it combines stain protection whilst giving the floor a subtle sheen appearance.
Looking at the floor when the last coat went on it was hard to believe the state it was in when I first arrived. Incidentally the owner who had inherited the house told me that he had not seen the floor look that good when his parents were alive as he remembered it from his childhood. It always makes the job more worthwhile when you hear stories like that.
This Slate Tiled floor belongs to a client who had recently bought an old Oast House in Hastings. They were in the process of restoring it and when lifting up the floor discovered an original slate floor underneath it. As the photos show it was in a very poor state and they were unsure whether to rip it up or see if it could be renovated.
On arrival they showed me the floor and told me of their dilemma; we provide a free no obligation home survey so after a thorough inspection I proceeded to run a test clean on a small section to see how well it would come up. This involved applying a 3-1 dilution of Tile Doctor Pro-Clean and working it in with a stiff brush and hand held buffer with a black scrubbing pad. I was very pleased to see the floor come up really clean and informed them I was very confident that not only could I get the floor clean it would amazing when finished. The clients were happy to hear the good news and gave me instructions to go ahead
Cleaning black slate floor tiles
On my return I applied the same strong 3:1 dilution of Tile Doctor Pro-Clean to the floor that I used before letting it soak into the tile for ten minutes before using a stiff brush and large buffing machine fitted with a scrubbing pad to clean the entire floor Slate tiled floor. When finished I went over the floor again looking for stubborn areas and spot treating them until I was happy with the result. Once happy I gave the floor a good rinse using fresh water to remove any trace of cleaning product from the floor and using a wet vacuum to remove the fluids and get the tiles as dry as possible.
Sealing Slate floor tiles
I left the floor for two days to allow time for it to completely dry out and returned to seal it using Tile Doctor Seal and Go. I applied four coats of sealer which gave the floor a fantastic finish and though the clients were initially weary of the shine I explained that it would dull down over a short period as it cured. Before leaving I gave them advice on how to keep the tiles clean and recommended the use of Tile Doctor Neutral Tile Cleaner which is a neutral PH cleaner that will not reduce the integrity and longevity of the sealer; they were both very happy with the end result as was I as the difference after was striking.
The pictures below are from a Travertine tiled en-suite bathroom at a house in the town of Horsham. A black mould had become ingrained in the pores of the shower tiles and the owner wanted it cleaned up before she rented the property out. The client had tried various well known supermarket products to remove the mould and grime from the tile, grout and sealing strip but without success so we got a call.
Cleaning Travertine Shower Tile
After explaining the cleaning process to the owner I set about the task by first cleaning the tiles and grout with a strong dilution of Tile Doctor Pro-Clean which was decanted into a spray bottle and sprayed onto the tile where it was allowed to soak in before being scrubbed in with a stiff brush. The wall was washed down with fresh water and stubborn areas re-treated. This worked well and removed all the discolouration and grime leaving the tiles and grout looking almost new.
Sealing Travertine Shower Tile
Travertine is a natural stone and to prevent grime penetrating into the pores of the tile making it difficult to clean it needs to be sealed so the next step was to let the tile and grout dry out followed by some assistance with a heat gun. Once they were dry we were able to seal them using two coats of Tile Doctor Colour Grow which is an impregnating sealer that also enhances the natural colour in the stone.
To finish the job we cleaned up the shower head and taps removing any calcium deposits and cleaned the shower screen. The old silicone sealer was discoloured and the only effective way to refresh it was to completely remove and replace it with new mould resistant silicone.
Once all the remedial work was complete the client came to have a look and was very pleased with the outcome as was I.